Stopping of Water Inrush
In the case of damp proofing work and renovation in the area of ingressing water, e.g. during tunnelling and in underground car parks, water frequently penetrates the construction through fissures and faults. In such cases Polyurethane foams and quick reacting Polyurethane resins, in particular have proven themselves to be very effective in the temporary arresting of water ingress.
Besides the foam formation and the short reaction time Polyurethane systems are especially suitable for the arresting of water ingress because they cannot mix with water.
- Good adherence properties even at adjacent water
- Reaction time can be adjusted < 15 sec.
- Flexible hence highly movement assimilation
- Penetrates even into haircracks
ECOCRYL Adjustable, low viscous, quickly reacting 3-component acrylate gel
- Quickly Reacting ECOCRYL
VARIOTITE Adjustable, rapid-reacting 3-component acrylate gel
- Very good elongation properties
- For renovation of dilatation joints
Foaming Polyurethane Resins
- Simple single component system with semi-elastic properties
- Also 1K flexible foam available
- High foaming volumes
PUR-O-STOP 1-component injection resin based on polyurethane
- Stopping of inrushing water
PUR-O-STOP FLEX 1-component injection resin based on polyurethane
- Stopping of inrushing water
- Highly flexible
- Extremely rapid reaction times
- High sealing and consolidation effect
- 2K foams also available in practical mix cartridge
PUR-O-STOP FS Very quickly reacting, from ridged to tough elastic, 2K polyurethane resin, which foams up in contact with water
PUR-O-STOP FS-L From ridged to tough elastic, 2K polyurethane resin, which foams up in contact with waterPUR-O-STOP FS-L
- Adjustable reaction time
- Groundwater friendly approved
PUR-O-STOP FS-F Extremely fast reacting, from ridged to tough elastic, 2K polyurethane resin, which foams up in contact with water
PUR-O-STOP FS-C Universal catalyst for shortening of reaction times of the PUR-O-STOP Systems like PUR-O-STOP HF, FS, FS-L, FS-F
PUR-O-STOP FS-TX Additive for increasing the viscosity of PUR-O-STOP FS, FS-L, FS-F.
PUR-O-STOP HF Foaming, quick reacting, 2K Polyurethane based resin
- For filling of cavities (<1m3)
- Pressurised water-proof
- For solidifying of soil and gravel
Acrylate gels for stopping of water inrush
It is possible to stop minor water ingress with the quick reacting acrylate gel VARIOTITE. To accomplish this, the product must be set to its most rapid reaction time (approx. 10-15 s), in that the relevant quantity of initiator is employed for the blending of the B component (see Technical data sheet).
The injection process should be carried out at a flow rate as high as possible via packers with a large inner diameter. Prior to this procedure the water ingress should be inhibited as far as possible. This can be accomplished using quick reacting cements such as F30 and F60 or by means of mechanical plugging, for example with cloths.
However, even quick reacting acrylate gels have their limitations in the stopping of ingressing water, because the acrylate gels are water soluble. On incidence of considerable faults through which the water can permeate the component, as well as in event of an extremely high flowing rate of the water, it would be more sensible to employ Polyurethane foams such as PUR-O-STOP to inhibit the water ingress, as these cannot be diluted by the water.
Polyurethane resin for stopping of water inrush
PUR-O-STOP and PUR-O-STOP HF are suitable for the temporary arresting of ingressing water. The fact that this is a temporary sealant has nothing whatsoever to do with the fact that PUR-O-STOP and PUR-O-STOP HF are not products for permanent application. Rather the injection against ingressing water has an impact on the recipe of the Polyurethane systems as these react with water.
If the water ratio is too high in comparison with the product quantity, foams could arise, which would not be durable on a permanent basis. Whereas if the water ratio matches the product quantity, permanently durable foams would be created. However, as the quantity of water on a building site cannot be verified, Polyurethane foams are customarily defined as temporary sealants.
A permanent sealing is accomplished by the retro-injection of two component Polyurethane resins, such as PUR-O-CRACK and PUR-O-RIP or of acrylate gels, such as RUBBERTITE and VARIOTITE.